Beko B100 Dishwasher Manual

The Beko B100 is a freestanding dishwasher with a 10-place setting capacity, featuring multiple wash programs, energy efficiency class A, delay start, child lock, and a salt and rinse aid indicator. It is designed for standard household use with dimensions of 60cm width, 85cm height, and 60cm depth. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Maintenance & Cleaning 9. Care & Safety 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control panel, Spray arms, Filter system, Salt container, Rinse aid dispenser, Detergent dispenser, Upper and lower baskets, Cutlery basket.

FeatureDescription
Wash ProgramsAuto, Intensive, Eco, Quick, Glass, Rinse
Capacity10 place settings
Energy RatingA (Energy efficient)
Delay StartUp to 24 hours
Child LockPrevents accidental program changes
Salt IndicatorAlerts when water softener salt is low
Rinse Aid IndicatorAlerts when rinse aid needs refilling
Half Load OptionSaves water and energy for smaller loads
Acoustic SignalBeeps when cycle is complete
Dimensions (WxHxD)60 x 85 x 60 cm

Installation

Unpack and inspect contents. Place on a level, stable floor near water and drain connections.

  1. Connect water supply: Attach inlet hose to cold water tap (max pressure 1 MPa).
  2. Connect drain hose: Ensure proper drainage into sink or standpipe (min height 40 cm).
  3. Level the appliance: Adjust feet to ensure dishwasher is stable and level.
  4. Plug into grounded power outlet (220-240V, 50Hz).

WARNING! Ensure water and electrical connections are secure to prevent leaks or electric shock. Do not use an extension cord.

First-Time Setup

Before first use, prepare the dishwasher.

  1. Remove transport materials: Take out all packaging inside the baskets and tub.
  2. Fill salt container: Add water softener salt to the dedicated container (only for hard water areas).
  3. Fill rinse aid dispenser: Pour rinse aid up to the MAX mark.
  4. Run a wash cycle: Select the Intensive program without dishes to clean the interior.
  5. Set water hardness: Use the control panel to set the hardness level according to your local water.

CAUTION! Use only dishwasher-specific salt and rinse aid. Do not use table salt.

Specifications

Controls and Settings

Control Panel: POWER, Program selection buttons, Delay Start, Half Load, Child Lock, Start/Pause.

Program Selection: Press repeatedly to cycle through Auto, Intensive, Eco, Quick, Glass, Rinse.

Delay Start: Press to set delay (1-24 hours).

Half Load: Activates when only one basket is used.

Child Lock: Press and hold for 3 seconds to activate/deactivate.

Indicators: Salt, Rinse Aid, End of cycle.

Loading the Dishwasher

Proper loading ensures optimal cleaning.

  1. Scrape off large food residues (no pre-rinsing required).
  2. Load lower basket: Pots, pans, plates, bowls (facing center).
  3. Load upper basket: Glasses, cups, saucers, small bowls.
  4. Cutlery basket: Place knives, forks, spoons (handles down for safety).
  5. Ensure items do not block spray arms or detergent dispenser.

Tip: Refer to the loading diagram in the manual for optimal placement.

Using Wash Programs

Select program based on soil level and dish type.

  1. Add detergent: Fill main wash compartment (and pre-wash if heavily soiled).
  2. Close detergent dispenser.
  3. Select program: Press program button until desired program lights up.
  4. Optional: Set Delay Start or Half Load.
  5. Press Start/Pause to begin cycle.
  6. Cycle ends with acoustic signal; open door slightly to let dishes dry.

WARNING! Use only dishwasher detergent. Do not use hand soap or laundry detergent.

Maintenance & Cleaning

Regular maintenance ensures longevity.

  1. Clean filter: Remove and rinse under water weekly.
  2. Clean spray arms: Check for blockages monthly.
  3. Refill salt: When salt indicator lights, add salt to container (water will overflow; this is normal).
  4. Refill rinse aid: When rinse aid indicator lights, fill dispenser to MAX.
  5. Wipe door seals and interior with damp cloth.

CAUTION! Unplug before any maintenance. Do not use abrasive cleaners.

Care & Safety

Unplug when not in use for extended periods. Keep door slightly open after cycle to prevent odors.

Safety: Do not open door during hot wash phases; steam may cause burns. Keep children away during operation.

Regulatory Information

CE marked. Complies with EU directives for low voltage and electromagnetic compatibility. Energy label according to EU regulation. For support, visit www.beko.com or contact customer service at 0333 207 9710 (UK).

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startPower, door, child lockCheck plug; ensure door closed; deactivate child lock.
Poor cleaning resultsLoading, detergent, filterReload dishes properly; use correct detergent; clean filter.
Water not drainingDrain hose blockageCheck drain hose for kinks; clean filter.
Salt indicator flashingSalt container emptyRefill with dishwasher salt.
Unusual noiseSpray arm obstructionCheck for items blocking spray arms.
Leaking waterHose connections, door sealTighten hoses; check door seal for damage.

Reset: Unplug for 5 minutes, then restart.

Service: 0333 207 9710; www.beko.com

Beko B100 Dishwasher Manual © - All Rights Reserved 2025