Beko Dishwasher BDFN26440WC Manual

The Beko BDFN26440WC is a 60cm wide, freestanding dishwasher with a stainless steel interior, A++ energy rating, and 14 place settings. It features 6 wash programs including Eco, Intensive, and Quick Wash, a half-load option, adjustable upper basket, salt and rinse aid indicators, delay start timer, and child lock. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Care & Maintenance 9. Safety Information 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control Panel, Spray Arms, Filters, Salt Container, Rinse Aid Dispenser, Upper and Lower Baskets, Cutlery Basket.

FeatureDescription
Energy RatingA++ for high energy efficiency
Place Settings14 standard place settings capacity
Wash Programs6 programs including Eco, Intensive, Quick
Half Load OptionReduces water and energy for smaller loads
Delay StartTimer to delay cycle start up to 24 hours
Child LockLocks control panel to prevent accidental changes
Salt & Rinse Aid IndicatorsLED indicators for refill reminders
Adjustable Upper BasketHeight adjustable for taller items
Stainless Steel InteriorDurable and hygienic interior lining
AquaStopLeak protection system

Installation

Unpack and inspect contents. Position near water supply, drain, and power outlet.

  1. Connect water inlet: Attach inlet hose to cold water tap using supplied connector.
  2. Connect drain hose: Place hose into sink or dedicated drain pipe (max height 1m).
  3. Level the appliance: Adjust feet to ensure dishwasher is level and stable.
  4. Plug into power outlet: Use a grounded socket.

WARNING! Ensure water and electrical connections are secure before first use. Do not kink hoses.

First-Time Setup

Before first wash, prepare the dishwasher.

  1. Fill salt container: Remove lower basket, unscrew salt cap, fill with special dishwasher salt (first time: add 1 litre of water), tighten cap.
  2. Fill rinse aid dispenser: Open dispenser lid on door, fill to MAX line, close lid.
  3. Select program: Run an Intensive wash cycle without dishes to clean interior and remove manufacturing residues.
  4. Adjust water hardness: Set built-in softener according to your local water hardness using the program button sequence.

CAUTION! Only use dishwasher salt, not table salt. Ensure salt cap is tightly closed.

Specifications

Controls and Settings

Access controls via the front panel. Main buttons: ON/OFF, PROGRAM SELECTION, HALF LOAD, DELAY START, CHILD LOCK, START/PAUSE.

Program Selection: Use button to cycle through Eco, Intensive, Auto, Quick, Delicate, Pre-Rinse. Corresponding LED will light.

Additional Functions: HALF LOAD (reduces consumption), DELAY START (1-24 hours), CHILD LOCK (press and hold for 3 seconds). Indicators: Salt (red), Rinse Aid (green), End of Cycle.

Loading the Dishwasher

For optimal cleaning, load items correctly.

  1. Scrape off large food residues; no need to pre-rinse.
  2. Lower Basket: Place pots, pans, plates, and larger items. Ensure spray arm can rotate freely.
  3. Upper Basket: Place cups, glasses, small bowls, and plastic items. Adjust height if needed.
  4. Cutlery Basket: Place knives, forks, spoons with handles down (except sharp knives).
  5. Use correct detergent: Fill main wash and pre-wash compartments in dispenser according to cycle and soil level.

Tip: Do not overload. Ensure items do not block the spray arms or detergent dispenser.

Using Wash Programs

Select program based on load type and soil level.

  1. Eco 50°C: Energy-efficient for normally soiled dishes (default daily cycle).
  2. Intensive 70°C: For heavily soiled pots, pans, and ovenware.
  3. Auto: Automatically adjusts time, temperature, and water based on soil sensors.
  4. Quick 58°C: Shorter cycle for lightly soiled loads.
  5. Delicate: Lower temperature for delicate glassware and china.
  6. Pre-Rinse: Rinses dishes to prevent odours if not washing immediately.

To start: Close door firmly, select program, press START/PAUSE. The cycle will begin.

WARNING! Do not open door during wash cycle; hot steam may escape.

Care & Maintenance

Regular maintenance ensures optimal performance.

CAUTION! Unplug appliance before cleaning filters or interior. Do not use sharp objects to clean spray arm holes.

Safety Information

Read all instructions before use.

Regulatory Information

This appliance complies with EU Directives 2014/35/EU (LVD), 2014/30/EU (EMC), and 2009/125/EC (ErP). Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check local regulations for disposal of packaging material. For support, visit www.beko.co.uk or contact the Beko Helpline at 0333 207 9710.

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startDoor not closed / No powerEnsure door is firmly closed; check power plug is in socket and switched on.
Poor washing resultsSpray arms blocked / Wrong programClean filters and spray arms; select a more intensive program for heavily soiled items.
Water not drainingDrain hose blocked/kinkedCheck drain hose for kinks or blockages; clean filter.
Salt indicator light onSalt container emptyRefill salt container with dishwasher salt.
Detergent not dissolvingDispenser lid blocked / Wet tabletsEnsure dispenser lid opens freely; keep detergent tablets dry before use.
Unusual noiseSpray arm hitting itemsRearrange load to ensure spray arms can rotate freely.

Reset: Turn appliance OFF and ON at mains for 1 minute if control panel is unresponsive.

Service: For issues not resolved above, contact Beko Customer Service: 0333 207 9710 or www.beko.co.uk.

Beko Dishwasher BDFN26440WC Manual © - All Rights Reserved 2025