beko dishwasher BDIN37541WP manual

The Beko BDIN37541WP is a built-in dishwasher with a stainless steel interior, 14 place settings capacity, 7 wash programs including Eco, Intensive, and Auto, A++ energy rating, 49 dB noise level, AquaIntense technology for stubborn stains, Half Load option, Delay Start up to 24 hours, child lock, and salt and rinse aid indicators. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Maintenance 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control panel with digital display, upper and lower baskets, cutlery basket, detergent dispenser, salt container, rinse aid dispenser, filter system, and inlet/drain hoses.

FeatureDescription
Capacity14 place settings
Wash Programs7 programs including Eco, Intensive, Auto, Quick, Glass, 90 Min, and Soak
Energy RatingA++
Noise Level49 dB
AquaIntense TechnologyTargeted spray for stubborn stains
Half Load OptionReduces water and energy for smaller loads
Delay StartProgram start delay up to 24 hours
Child LockPrevents accidental program changes
Salt & Rinse Aid IndicatorsLED indicators for refill reminders
Stainless Steel InteriorDurable and hygienic

Installation

Unpack and inspect contents. Ensure installation space meets dimensions.

  1. Position dishwasher: Place in prepared cabinet space under countertop.
  2. Connect water supply: Attach inlet hose to cold water tap (max pressure 1 MPa).
  3. Connect drain hose: Route to sink drain or standpipe (min height 40 cm).
  4. Electrical connection: Plug into grounded 220-240V, 50Hz outlet.
  5. Level the appliance: Adjust feet for stability.

WARNING! Installation must be performed by qualified personnel. Ensure water and electrical connections are secure to prevent leaks or shock.

First-Time Setup

Before first use, prepare dishwasher.

  1. Remove shipping materials: Take out all interior packaging and transit bolts.
  2. Fill salt container: Unscrew cap, add 1 kg of special dishwasher salt, then refill with water until it overflows.
  3. Fill rinse aid dispenser: Open lid, pour rinse aid up to MAX mark.
  4. Run initial wash: Select Intensive program without dishes to clean interior.
  5. Set water hardness: Adjust setting based on local water hardness using program button combination.

CAUTION! Use only dishwasher salt and rinse aid. Do not use table salt or liquid detergent in salt container.

Specifications

Controls and Settings

Control Panel: ON/OFF button, Program selection buttons, Delay Start, Half Load, Child Lock, Start/Pause.

Programs: Eco (energy saving), Intensive (for heavily soiled), Auto (sensor-based), Quick (58 min), Glass (gentle), 90 Min (standard), Soak (pre-wash).

Settings: Adjust water hardness (H1-H5), activate acoustic signals, reset filter indicator. Use Program + Start buttons for 3 seconds to enter settings mode.

Loading the Dishwasher

Proper loading ensures optimal cleaning.

  1. Scrape off large food residues before loading.
  2. Lower basket: For plates, pots, pans. Adjust height if needed.
  3. Upper basket: For glasses, cups, small plates. Tilt glasses for secure placement.
  4. Cutlery basket: Place knives pointing down, spoons and forks mixed.
  5. Ensure spray arms rotate freely; do not block with large items.

Tip: Place heavily soiled items facing center. Do not overload baskets.

Using Wash Programs

Select program based on soil level and dish type.

  1. Add detergent: Fill main wash compartment for pre-wash and main wash. Use tablet in detergent compartment.
  2. Select program: Press Program button until desired program LED lights.
  3. Optional settings: Press Half Load for fewer dishes; Delay Start to set start time.
  4. Start: Press Start/Pause. Door locks automatically.
  5. After cycle: Wait for end signal; open door slightly to let steam escape before unloading.

WARNING! Use only dishwasher detergents. Do not open door during hot wash phases to avoid steam burns.

Maintenance

Regular maintenance ensures performance and longevity.

  1. Clean filters: Twist and lift out coarse and fine filters; rinse under tap weekly.
  2. Check spray arms: Remove and clear holes if blocked.
  3. Refill salt: When salt indicator lights, add salt to container (approx. every 2 months).
  4. Refill rinse aid: When rinse aid indicator lights, fill to MAX mark.
  5. Clean interior: Run empty wash with vinegar or dishwasher cleaner monthly.

CAUTION! Unplug before maintenance. Do not use abrasive cleaners on interior.

Care & Cleaning

Exterior: Wipe control panel and door with damp cloth. Use mild detergent if needed.

CAUTION! Do not use solvents, abrasive powders, or steel wool. Keep control panel dry.

Regulatory Information

CE compliant. Meets EU Ecodesign and Energy Label regulations. Waste electrical products must not be disposed of with household waste. Please recycle according to local regulations. For support, visit www.beko.com or contact local service center.

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher not startingPower supply, door not closedCheck plug, fuse, circuit breaker; ensure door is properly closed.
Poor washing resultsSpray arms blocked, incorrect loadingClean spray arms; rearrange dishes; use correct detergent amount.
Water not drainingFilter clogged, drain hose kinkedClean filter; check drain hose for obstructions.
Leaking waterInlet hose loose, door seal damagedTighten connections; check door seal and replace if damaged.
Unusual noiseSpray arm hitting dishes, foreign objectRearrange load; check for small objects in pump area.
Salt indicator remains onSalt container empty, setting incorrectRefill salt; check water hardness setting.

Reset: Unplug for 5 minutes, then restart.

Service: Contact authorized Beko service center. Do not attempt repairs yourself.

Beko Dishwasher BDIN37541WP User Manual © - All Rights Reserved 2025