beko dishwasher DFN 15X10 manual

The Beko DFN 15X10 is a freestanding dishwasher with a 15-place setting capacity, featuring 10 wash programs, an A++ energy rating, and a 50 dB noise level. It includes a half-load function, delay timer, child lock, and salt and rinse aid indicators. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Care & Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Control panel, Upper and lower baskets, Cutlery basket, Filter system, Salt and rinse aid dispensers, Water inlet and drain hoses.

FeatureDescription
Capacity15 place settings
Energy RatingA++
Noise Level50 dB
Wash Programs10 programs including Intensive, Eco, Quick, Glass
Half Load FunctionFor washing fewer dishes, saving water and energy
Delay TimerDelay start up to 24 hours
Child LockPrevents accidental program changes
Salt & Rinse Aid IndicatorsLights alert when refills are needed
DisplayDigital display with remaining time and program info
Dimensions (HxWxD)85 x 60 x 60 cm

Installation

Unpack and inspect contents. Position near water supply, drain, and power outlet.

  1. Connect water supply: Attach inlet hose to cold water tap (max pressure 1 MPa).
  2. Connect drain hose: Place into sink or dedicated drain pipe (min height 40 cm).
  3. Level the appliance: Adjust feet to ensure dishwasher is stable and level.
  4. Plug into grounded power outlet (220-240V, 50Hz).

WARNING! Ensure water and electrical connections are secure before first use. Do not kink hoses.

First-Time Setup

Before first wash, prepare the dishwasher.

  1. Fill salt dispenser: Remove lower basket, unscrew cap, add 1 kg of dishwasher salt, then refill with water until it overflows.
  2. Fill rinse aid dispenser: Open lid on inner door, pour rinse aid up to "MAX" mark.
  3. Run initial empty cycle: Select the Intensive program without dishes to clean interior.
  4. Set water hardness: Use program button combination to match your local water hardness level (see manual).

CAUTION! Only use dishwasher salt and rinse aid specifically designed for dishwashers.

Specifications

Controls and Settings

Access programs and settings via the control panel on the top of the door.

Buttons: POWER ON/OFF, PROGRAM SELECTION, DELAY START, HALF LOAD, CHILD LOCK, START/PAUSE.

Program Selection: Scroll through programs (Intensive, Eco, Quick, Glass, Auto, etc.). Delay Timer: Set start delay from 1 to 24 hours. Half Load: Activates when only one basket is loaded. Child Lock: Press and hold HALF LOAD and DELAY for 3 seconds to activate/deactivate. Display: Shows selected program, remaining time, and status icons (Salt, Rinse Aid).

Loading the Dishwasher

Proper loading ensures optimal cleaning.

  1. Scrape off large food residues; no need to pre-rinse.
  2. Lower basket: For pots, pans, plates, and larger items.
  3. Upper basket: For glasses, cups, saucers, and smaller dishes.
  4. Cutlery basket: Place knives, forks, spoons with handles down (except sharp knives).
  5. Ensure spray arms can rotate freely and items do not block detergent dispenser.

Tip: Place heavily soiled items facing the center. Do not overload baskets.

Using Wash Programs

Select program based on soil level and dish type.

  1. Add detergent: Use powder or tablet in main wash compartment. For pre-wash (heavily soiled), add a small amount to the pre-wash compartment.
  2. Close door securely.
  3. Select program: Press POWER, then PROGRAM button to cycle through options.
  4. Optional: Set DELAY or HALF LOAD.
  5. Start: Press START/PAUSE. The display will show remaining time.
  6. At end of cycle: A beep will sound. Wait a few minutes before opening to allow steam to dissipate.

WARNING! Only use detergents and additives meant for dishwashers. Do not open door during a hot wash cycle.

Care & Maintenance

Regular maintenance ensures longevity and performance.

Cleaning the filter: Turn filter assembly counterclockwise, lift out. Rinse under tap to remove debris. Reinsert and turn clockwise to lock.

Cleaning the spray arms: Check for blockages in holes. Remove by pulling upwards and rinse.

Exterior: Wipe with a damp cloth and mild detergent. Do not use abrasive cleaners.

Monthly care: Run an empty cycle with a dishwasher cleaner or a cup of vinegar to remove limescale and odors.

CAUTION! Unplug appliance before any maintenance. Never remove filter during a cycle.

Regulatory Information

This appliance complies with EU Directives 2014/35/EU (LVD), 2014/30/EU (EMC), and 2009/125/EC (ErP). Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority for recycling advice. For support, visit www.beko.com or contact your local Beko service center.

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startDoor not closed / No powerEnsure door is firmly shut. Check power cord is plugged in and outlet works.
Poor washing resultsClogged filter / Wrong programClean filter system. Select a more intensive program for heavily soiled loads.
Water not drainingDrain hose blocked/kinkedCheck drain hose for blockages or kinks. Ensure height is correct (40-100 cm).
Salt indicator light onSalt level lowRefill salt dispenser with dishwasher salt.
Unusual noiseSpray arm hitting itemsRearrange load so spray arms rotate freely. Check for small objects in pump area.
Error code on displayVarious faultsConsult the error code table in the full manual. Common codes: E1 (water inlet), E2 (drainage).

Reset: Turn off power at socket for 5 minutes, then restart.

Service: For persistent issues, contact authorized Beko service. Do not attempt repairs yourself.

beko dishwasher DFN 15X10 manual © - All Rights Reserved 2025