beko dishwasher DFN 26443 G manual

The Beko DFN 26443 G is a freestanding dishwasher with a capacity for 14 place settings, featuring an A++ energy rating, 6 wash programs, a delay timer, and AquaStop leak protection. It includes a stainless steel interior, adjustable upper basket, salt and rinse aid indicators, and a child lock. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Care & Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Control Panel, Spray Arms, Filter System, Detergent Dispenser, Salt Container, Rinse Aid Dispenser, Upper and Lower Baskets, Cutlery Basket.

FeatureDescription
Capacity14 standard place settings
Energy RatingA++ (Energy Efficient)
Wash Programs6 programs including Intensive, Eco, Quick, Glass, etc.
Delay TimerProgram start delay from 1 to 24 hours
AquaStopFull protection against water leaks
Child LockSafety lock for control panel
DisplayDigital display with remaining time and program indicators
Half Load OptionEco wash for smaller loads
Adjustable Upper BasketHeight adjustable for taller items
Salt & Rinse Aid IndicatorsLED indicators for refill reminders

Installation

Unpack and inspect contents. Position near water inlet, drain, and power socket.

  1. Connect water inlet: Attach supplied hose to cold water tap (max pressure 1 MPa).
  2. Connect drain hose: Ensure proper height (40-100 cm from floor) to prevent siphoning.
  3. Level the appliance: Adjust feet to ensure dishwasher is stable and level.
  4. Plug into grounded power socket.

WARNING! Ensure water and electrical connections are secure before first use. Do not kink hoses.

First-Time Setup

Before first wash, prepare the dishwasher.

  1. Fill salt container: Remove lower basket, unscrew cap, fill with special dishwasher salt (first use: add 1 liter of water), tighten cap.
  2. Fill rinse aid dispenser: Open lid, fill to MAX line, close lid.
  3. Select program: Run an empty wash on the Intensive program with detergent to clean interior.
  4. Adjust water hardness: Set hardness level according to local water supply using the program buttons (see manual).

CAUTION! Use only dishwasher salt, not table salt. Ensure salt cap is tightly closed.

Specifications

Controls and Settings

Access programs and settings via the control panel on the top of the door.

Buttons: POWER ON/OFF, PROGRAM SELECTION (Intensive, Eco, Quick, Glass, Auto, Rinse), DELAY START (1-24h), HALF LOAD, CHILD LOCK.

Display: Shows selected program, remaining time, salt and rinse aid indicators, and error codes.

Settings: Water hardness level (1-5), acoustic signal on/off, rinse aid dosage (1-5). Access settings by holding PROGRAM and DELAY buttons for 3 seconds.

Loading the Dishwasher

For optimal washing results, load correctly.

  1. Scrape off large food residues.
  2. Load lower basket: Pots, pans, plates. Ensure items do not block spray arms.
  3. Load upper basket: Glasses, cups, saucers, small bowls.
  4. Cutlery basket: Place knives, forks, spoons with handles down (except sharp knives).
  5. Adjust upper basket height if needed for taller items.
  6. Add detergent to dispenser (powder, tablets, or gel).

Tip: Do not overload. Place delicate items in the upper basket.

Using Wash Programs

Select program based on soil level and dish type.

  1. Turn on: Press POWER.
  2. Select program: Press PROGRAM button repeatedly to cycle through options.
  3. Optional settings: Press DELAY for delayed start, HALF LOAD for smaller loads.
  4. Start: Close door firmly. The program starts automatically.
  5. During wash: Display shows remaining time. Child lock can be activated.
  6. End of cycle: Acoustic signal sounds (if enabled). Open door slightly to let steam escape.

Program Guide: Intensive (heavily soiled, 70°C), Eco (normally soiled, 50°C), Quick (lightly soiled, 45°C), Glass (delicate glassware, 40°C), Auto (sensors adjust), Rinse (rinse only).

Care & Maintenance

Regular maintenance ensures performance and longevity.

  1. Clean filter: Remove lower basket, twist and lift out filter assembly, rinse under tap weekly.
  2. Clean spray arms: Check for blockages, rinse holes.
  3. Check salt and rinse aid: Refill when indicators light.
  4. Exterior: Wipe with damp cloth, mild detergent. Do not use abrasive cleaners.
  5. Monthly cleaning: Run empty wash with a dishwasher cleaner or vinegar to remove limescale.

CAUTION! Unplug before any maintenance. Do not run dishwasher without filter.

Regulatory Information

This appliance complies with EU Directives 2014/35/EU (LVD), 2014/30/EU (EMC), and 2009/125/EC (ErP). Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. Check local regulations. For support, visit www.beko.com or contact your local Beko service center.

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startPower, door, child lockCheck plug, socket, and fuse. Ensure door is closed properly. Deactivate child lock.
No water intakeTap, filter, hoseEnsure water tap is open. Check inlet hose for kinks. Clean inlet filter.
Poor washing resultsLoading, detergent, spray armsLoad dishes correctly. Use correct amount of fresh detergent. Clean filter and spray arms.
Water not drainingDrain hose, filter blockageCheck drain hose for kinks or blockage. Clean filter system.
Error code on displayVarious faultsRefer to manual error code list (e.g., E1, E2). Reset by turning power off/on. If persistent, call service.
LeakingDoor seal, hose connectionsCheck door seal is clean and undamaged. Ensure all hose connections are tight.

Reset: Turn off power at socket for 5 minutes, then restart.

Service: Contact authorized Beko service. Do not attempt repairs yourself.

beko dishwasher DFN 26443 G manual © - All Rights Reserved 2025