Beko Dishwasher DFN16420X Manual

The Beko DFN16420X is a freestanding dishwasher with a 14-place setting capacity, A++ energy rating, and multiple wash programs. It features a stainless steel interior, digital display, delay start, child lock, half-load option, and rinse aid/salt indicators. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Maintenance & Cleaning 9. Safety Features 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Stainless steel tub, upper and lower baskets, cutlery basket, detergent dispenser, digital control panel, water inlet/outlet hoses, filter system.

Feature	Description
Capacity	14 place settings
Energy Rating	A++
Digital Display	Shows program time, delay start, and error codes
Wash Programs	Auto, Intensive, Eco, Quick, Glass, Half Load
Delay Start	Programmable up to 24 hours
Child Lock	Prevents accidental program changes
Rinse Aid Indicator	LED alerts when rinse aid is low
Salt Indicator	LED alerts when water softener salt is low
Acoustic Signal	Optional end-of-cycle beep
Dimensions (HxWxD)	85cm x 60cm x 60cm

Installation

Unpack and inspect contents. Ensure location is level and near water/drain connections.

Connect water inlet: Attach supplied hose to cold water tap (max pressure 1MPa).
Connect drain hose: Place in sink or connect to waste pipe (min height 40cm).
Level the appliance: Adjust feet until dishwasher is stable and level.
Plug into grounded power outlet (220-240V, 50Hz).

WARNING! Do not use extension cords. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first use, remove transport locks and prepare the dishwasher.

Fill salt dispenser: Unscrew cap, add 1kg of dishwasher salt, then refill with water.
Fill rinse aid: Open dispenser, fill to MAX line with rinse aid liquid.
Run empty wash: Select Intensive program without dishes to clean interior.
Set water hardness: Use program buttons to set according to local water hardness (see manual).

CAUTION! Only use dishwasher-specific salt and rinse aid. Do not mix with detergent.

Specifications

Model: DFN16420X
Type: Freestanding dishwasher
Capacity: 14 place settings
Energy Consumption: 0.95 kWh per cycle (Eco program)
Water Consumption: 10 liters per cycle (Eco program)
Noise Level: 49 dB(A)
Power Supply: 220-240V, 50Hz
Max Inlet Pressure: 1 MPa (10 bar)
Programs: Auto, Intensive (70°C), Eco (50°C), Quick (30 min), Glass, Half Load
Special Functions: Delay start (1-24h), Child lock, Extra drying

Controls and Settings

Control Panel: POWER button, Program selector, DELAY START, CHILD LOCK, START/PAUSE.

Program Selection: Press PROGRAM button to cycle through options. Display shows duration and remaining time.

Settings: Water hardness (1-5), acoustic signal on/off, rinse aid dosage (1-5), reset filter indicator. Use combination of buttons (hold START + PROGRAM for 3 seconds) to access service menu.

Loading the Dishwasher

Proper loading ensures optimal cleaning and prevents damage.

Scrape off large food residues (no pre-rinsing needed).
Load lower basket: Plates, pots, pans facing center.
Load upper basket: Glasses, cups, bowls.
Cutlery basket: Place knives pointing down, mixed cutlery types.
Ensure spray arms rotate freely and items don't block detergent dispenser.

Tip: Refer to loading diagrams in manual for optimal arrangement.

Using Wash Programs

Select program based on soil level and dish type.

Add detergent: Fill main wash compartment (and pre-wash if heavily soiled).
Select program: Press PROGRAM until desired program lights up.
Optional settings: Press DELAY to set start time; press EXTRA DRY if needed.
Start: Close door firmly and press START/PAUSE.
During cycle: Press START/PAUSE to pause; door locks during wash phases.
After completion: Wait for door lock to release (approx. 2 min after end beep).

WARNING! Use only dishwasher detergent. Do not open door during hot wash phases.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

Weekly: Clean filter assembly (rotate and lift out, rinse under water). Wipe door seals with damp cloth.

Monthly: Check and clean spray arms (remove by unscrewing, clear any blockages). Run empty wash with dishwasher cleaner.

As needed: Refill salt and rinse aid when indicators light. Descale if in hard water area (use citric acid or dishwasher descaler).

CAUTION! Unplug before maintenance. Do not use abrasive cleaners on interior.

Safety Features

Child Lock: Press and hold CHILD LOCK for 3 seconds to activate/deactivate. Door Lock: Automatically locks during wash cycles. Overflow Protection: Float switch stops water if detected. Thermal Cut-out: Prevents overheating.

Regulatory Information

CE marked. Complies with EU directives 2014/35/EU (LVD), 2014/30/EU (EMC), and 2009/125/EC (ErP). Waste electrical products must not be disposed of with household waste. Please recycle where facilities exist. For support, visit www.beko.com or contact local service center.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Dishwasher won't start	Door not closed/power	Ensure door fully closed; check power outlet; circuit breaker.
Poor cleaning results	Loading/detergent	Check loading; use correct detergent amount; clean filter.
Water not draining	Drain hose blocked	Check hose for kinks/blockages; clean filter.
Error code E1/E2	Water inlet issue	Check water tap is on; inlet hose not kinked; filter clean.
Error code E3/E4	Drain issue	Check drain hose height (min 40cm); remove blockage.
Leaking water	Door seal/hose	Check door seal for debris; ensure hoses connected tightly.
Noisy operation	Spray arm/items	Ensure spray arms rotate freely; check dishes not touching.

Reset: Unplug for 5 minutes, then restart. If error persists, contact service.

Service: Check warranty card; contact authorized Beko service center.