beko dishwasher DFS05011W manual

The Beko DFS05011W is a freestanding dishwasher with a 10-place setting capacity, A++ energy rating, and 5 wash programs. It features a digital display, delay start function, half load option, child lock, and salt and rinse aid indicators. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Detergents and Additives 8. Care & Cleaning 9. Troubleshooting 10. Technical Data 11. Warranty Information

Features at a Glance

Key components: Stainless steel interior, upper and lower baskets, cutlery basket, detergent dispenser, salt container, rinse aid dispenser, digital display, and control panel.

FeatureDescription
Capacity10 place settings
Energy RatingA++
Wash Programs5 programs (Eco, Intensive, Normal, Rapid, Glass)
Digital DisplayShows remaining time, program, and status icons
Delay StartProgram start delay from 1 to 24 hours
Half Load OptionReduces water and energy consumption for smaller loads
Child LockLocks control panel to prevent accidental changes
Salt & Rinse Aid IndicatorsLED indicators alert when refills are needed
AquaStopProtection against water leaks
Dimensions (HxWxD)85 x 60 x 60 cm

Installation

Unpack and inspect contents. Ensure location is level, near water supply, drain, and power outlet.

  1. Remove transit bolts: Locate at rear, unscrew and remove using spanner provided.
  2. Connect water supply: Attach inlet hose to cold water tap (max pressure 1 MPa).
  3. Connect drain hose: Place into sink or connect to waste pipe (min height 40 cm).
  4. Level the appliance: Adjust feet using a spanner to ensure stability.
  5. Plug into power outlet: Use a grounded socket (220-240V, 50Hz).

WARNING! Do not install near heat sources. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first use, prepare the dishwasher.

  1. Fill salt container: Open cap, pour in 1 kg of dishwasher salt, then fill with water until it overflows. Tighten cap.
  2. Fill rinse aid dispenser: Open lid, pour rinse aid up to MAX mark, close lid.
  3. Run a wash cycle: Select Intensive program without dishes to clean interior and remove manufacturing residues.
  4. Set water hardness: Consult manual table; press and hold P1 and P3 buttons for 3 seconds, then use program buttons to select level (1-5).

CAUTION! Use only dishwasher salt and rinse aid. Do not use table salt.

Specifications

Controls and Settings

Control Panel: ON/OFF button, Program selection buttons (Eco, Intensive, Normal, Rapid, Glass), Delay Start button, Half Load button, Start/Pause button.

Display Icons: Salt indicator, Rinse aid indicator, Child lock, Delay time, Program duration, End of cycle.

Program Selection: Press corresponding button; selected program light will illuminate. Delay Start: Press Delay button, then use +/- to set hours (1-24). Half Load: Press button to activate for smaller loads. Child Lock: Press and hold P1 and P2 for 3 seconds to activate/deactivate.

Loading the Dishwasher

Proper loading ensures optimal cleaning.

  1. Scrape off large food residues; no need to pre-rinse.
  2. Lower basket: Plates, pots, pans. Place facing center, tilted downwards.
  3. Upper basket: Cups, glasses, small bowls. Secure in racks.
  4. Cutlery basket: Place knives (handles up), spoons and forks mixed to prevent nesting.
  5. Adjust upper basket height: Lift levers on both sides to raise/lower.

Tip: Do not overload. Ensure spray arms can rotate freely.

Using Detergents and Additives

Use only dishwasher-specific products.

  1. Detergent: Fill main dispenser (compartment marked I). Use tablet, powder, or gel. For pre-wash (if heavily soiled), fill compartment marked PRE.
  2. Rinse aid: Automatically dispensed. Refill when indicator light is on.
  3. Salt: Regenerates water softener. Refill when indicator light is on.
  4. Dosage: Follow detergent manufacturer instructions. Adjust rinse aid dosage via dial inside dispenser (1-6).

WARNING! Do not use hand wash detergent. Keep products out of children's reach.

Care & Cleaning

Regular maintenance ensures longevity.

  1. Clean filters: Remove lower basket, twist and lift out coarse and fine filters. Rinse under tap.
  2. Clean spray arms: Remove by pulling upwards, check nozzles for blockages.
  3. Wipe door seals and interior: Use damp cloth with mild detergent.
  4. Exterior: Clean with soft cloth and mild detergent. Do not use abrasive cleaners.
  5. Monthly: Run empty cycle with dishwasher cleaner or vinegar to remove limescale.

CAUTION! Unplug before cleaning. Do not use steam cleaners.

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startPower, door, child lockCheck plug, fuse, ensure door closed properly, deactivate child lock.
Poor cleaning resultsLoading, detergent, filtersRearrange load, use correct detergent amount, clean filters.
Water not drainingDrain hose, filter blockageCheck hose for kinks, clean filter, ensure drain height correct.
Salt/Rinse aid indicator onLow levelRefill salt or rinse aid container.
Unusual noiseSpray arm, dishesEnsure spray arms rotate freely, check dishes not obstructing arms.
Error code E1Water supply issueCheck tap is on, inlet hose not kinked, filter not clogged.

Reset: Unplug for 5 minutes, then restart.

Technical Data

Warranty Information

Beko provides a 2-year manufacturer's warranty for parts and labor from date of purchase. Warranty covers defects in materials and workmanship under normal domestic use. Not covered: Damage from improper installation, misuse, commercial use, or unauthorized repairs. To register warranty or request service, visit www.beko.com or contact local service center. Keep purchase receipt as proof of date.

beko dishwasher DFS05011W manual © - All Rights Reserved 2025