Beko Dishwasher DIN26422 Manual

The Beko DIN26422 is a built-in dishwasher with 14 place settings, A++ energy rating, 5 wash programs, half-load option, adjustable upper basket, salt and rinse aid indicators, child lock, delay start, and acoustic signal. Features include AquaIntense technology for stubborn stains, glass protection program, and quick wash cycle. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Detergents 8. Maintenance & Care 9. Safety Features 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Control panel with digital display, upper and lower baskets, cutlery basket, filter system, salt container, rinse aid dispenser, water inlet and drain hoses.

FeatureDescription
Capacity14 place settings
Energy RatingA++ (most efficient)
Wash Programs5 programs including Intensive, Eco, Quick, Glass, and Auto
Half Load OptionReduces water and energy for smaller loads
Adjustable Upper BasketHeight adjustable for taller items
Salt & Rinse Aid IndicatorsLED indicators for refill reminders
Child LockPrevents accidental program changes
Delay StartProgram start delay up to 24 hours
Acoustic SignalAudible end-of-cycle signal
AquaIntense TechnologyTargeted spray for stubborn stains

Installation

Unpack and inspect contents. Ensure proper electrical and water connections.

  1. Position dishwasher: Place in prepared cabinet space with adequate ventilation.
  2. Connect water supply: Attach inlet hose to cold water tap (max pressure 1 MPa).
  3. Connect drain hose: Ensure proper drainage without kinks (height 40-100 cm).
  4. Electrical connection: Connect to 220-240V, 50Hz grounded outlet.
  5. Level the appliance: Adjust feet for stability.

WARNING! Installation must be performed by qualified personnel. Ensure water and electrical connections are secure before first use.

First-Time Setup

Before first use, prepare the dishwasher with salt and rinse aid.

  1. Fill salt container: Remove lower basket, unscrew cap, add 1kg special dishwasher salt, replace cap.
  2. Fill rinse aid dispenser: Open dispenser lid, fill to MAX line, close lid.
  3. Set water hardness: Use program buttons to set according to local water hardness (1-5).
  4. Run initial cycle: Run empty dishwasher on Intensive program without dishes.

CAUTION! Use only dishwasher salt in salt container. Never use table salt.

Specifications

Controls and Settings

Control Panel: ON/OFF button, program selection buttons, delay start, half load, child lock, start/pause.

Program Selection: Press program button repeatedly to cycle through options. LED indicates selected program.

Additional Functions: Delay Start (1-24 hours), Half Load (reduces consumption), Child Lock (hold for 3 seconds to activate/deactivate).

Display Indicators: Salt warning (red), Rinse aid warning (yellow), End of cycle (green), Door open (flashing).

Loading the Dishwasher

Proper loading ensures optimal cleaning results.

  1. Scrape off large food residues before loading.
  2. Lower basket: For plates, pots, pans, and larger items.
  3. Upper basket: For glasses, cups, saucers, and smaller items.
  4. Cutlery basket: Place knives pointing down, spoons and forks mixed.
  5. Adjust upper basket: Lift to higher position for taller items.
  6. Ensure spray arms rotate freely without obstruction.

Tip: Do not overload. Place items facing center for better water coverage.

Using Detergents

Use only dishwasher-specific detergents.

  1. Detergent dispenser: Fill main compartment with powder or tablet detergent.
  2. Pre-wash compartment: For heavily soiled loads, add small amount of detergent.
  3. Detergent type: Use tablets, powder, or gel specifically for dishwashers.
  4. Dosage: Follow manufacturer instructions based on water hardness and soil level.
  5. Rinse aid: Automatically dispensed during final rinse for spot-free drying.

WARNING! Never use regular dish soap. It creates excessive suds and can damage the appliance.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

  1. Clean filter weekly: Remove lower basket, twist filter assembly counterclockwise, rinse under water.
  2. Clean spray arms monthly: Remove and check for clogged holes, rinse thoroughly.
  3. Wipe door seals: Clean with damp cloth to prevent leaks.
  4. Descale periodically: Use dishwasher descaler every 2-3 months in hard water areas.
  5. Clean interior: Run empty cycle with dishwasher cleaner every month.

CAUTION! Unplug before maintenance. Never use abrasive cleaners or tools.

Safety Features

Child Lock: Prevents program changes during operation. Door Safety: Dishwasher stops if door opened during cycle. Overflow Protection: Automatic shut-off if water level too high. Thermal Cut-out: Prevents overheating.

Regulatory Information

CE compliant according to EU directives. Energy label class A++. Waste Electrical and Electronic Equipment (WEEE) directive compliant. For disposal, contact local authorities. Manufacturer: Beko PLC. For support, visit www.beko.com or contact customer service at 0333 207 9710 (UK).

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startPower/doorCheck power supply; ensure door closed properly; check child lock.
Poor cleaning resultsLoading/detergentImprove loading; use correct detergent amount; clean filter.
Water not drainingDrain hose/filterCheck drain hose for kinks; clean filter; ensure proper installation height.
Salt indicator stays onSalt level/regenerationRefill salt container; run regeneration cycle if needed.
Unusual noiseSpray arms/itemsCheck for items obstructing spray arms; ensure proper loading.
Leaking waterDoor seal/hosesCheck door seal for debris; tighten hose connections; level the appliance.

Reset: Unplug for 5 minutes, then restart.

Service: 0333 207 9710; www.beko.com

Beko Dishwasher DIN26422 Manual © - All Rights Reserved 2025