Beko Dishwasher DIN28426 Manual

The Beko DIN28426 is a freestanding dishwasher featuring multiple wash programs, energy efficiency, adjustable racks, delay start, child lock, and salt/rinse aid indicators. It is designed for standard household use with a capacity for up to 12 place settings. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Care & Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Control Panel, Spray Arms, Filter System, Detergent Dispenser, Salt Container, Rinse Aid Dispenser, Upper and Lower Racks, Cutlery Basket.

Feature	Description
Wash Programs	Auto, Intensive, Eco, Quick, Glass, Rinse
Delay Start	Program start delay from 1 to 24 hours
Child Lock	Locks control panel to prevent accidental changes
Salt Indicator	LED indicates when water softener salt is low
Rinse Aid Indicator	LED indicates when rinse aid needs refilling
Adjustable Upper Rack	Height adjustable for taller items
Half Load Option	Reduces water and energy for smaller loads
Acoustic Signal	Audible beep at end of program (can be disabled)
Energy Class	A++ for energy efficiency
Water Protection	AquaStop anti-flood system

Installation

Unpack and inspect contents. Position near water inlet, drain, and power outlet.

Level the dishwasher: Adjust feet until unit is stable and level.
Connect water supply: Attach inlet hose to cold water tap (max pressure 1 MPa).
Connect drain hose: Ensure proper height (40-100 cm from floor) to prevent siphoning.
Plug into grounded power outlet (220-240V, 50Hz).

WARNING! Ensure water and electrical connections are secure before first use. Do not kink hoses.

First-Time Setup

Before first wash, prepare the dishwasher.

Fill salt container: Remove lower rack, unscrew cap, add 1 kg of special dishwasher salt, then run a short program without dishes.
Fill rinse aid dispenser: Open lid, fill to MAX line, close securely.
Select language: Press and hold PROGRAM + DELAY for 3 seconds to cycle through languages.
Run initial empty cycle: Select Intensive program without detergent to clean interior.

CAUTION! Only use dishwasher salt in the softener unit. Do not use table salt.

Specifications

Type: Freestanding Dishwasher.
Capacity: 12 place settings.
Energy Consumption: 0.95 kWh per cycle (Eco program).
Water Consumption: 10 liters per cycle (Eco program).
Noise Level: 49 dB(A).
Programs: Auto (45-65°C), Intensive (70°C), Eco (50°C), Quick (35°C), Glass (40°C), Rinse.
Dimensions (HxWxD): 85 x 60 x 60 cm.
Power Supply: 220-240V, 50Hz.
Inlet Water Pressure: 0.03 - 1 MPa.

Controls and Settings

Control Panel: POWER, PROGRAM selector, DELAY START, CHILD LOCK, START/PAUSE.

Program Selection: Turn knob to select desired wash program. LED indicates selection.

Delay Start: Press DELAY repeatedly to set hours (1-24). LED blinks during countdown.

Child Lock: Press and hold CHILD LOCK for 3 seconds to activate/deactivate.

Salt/Rinse Aid Indicators: Illuminate when refill is required.

Half Load: Press PROGRAM + DELAY simultaneously when loading only one rack.

Loading the Dishwasher

Proper loading ensures optimal cleaning.

Scrape off large food residues; no need to pre-rinse.
Load lower rack: Pots, pans, plates (facing center).
Load upper rack: Glasses, cups, bowls (angled downward).
Cutlery basket: Place knives pointing down; mix items for separation.
Adjust upper rack height: Lift levers on both sides to raise/lower.
Ensure spray arms rotate freely and are not blocked.

Tip: Do not overload. Place delicate items on upper rack away from heating element.

Using Wash Programs

Select program based on soil level and dish type.

Add detergent: Fill main wash compartment for pre-wash and main wash; use tablets or powder.
Close door securely.
Select program with knob.
Optional: Set DELAY START if needed.
Press START/PAUSE. Program begins, door locks.
At end of cycle, acoustic signal sounds (if enabled). Wait a few minutes before opening to avoid steam.

WARNING! Only use detergents designed for dishwashers. Do not open door during high-temperature cycles.

Care & Maintenance

Regular maintenance ensures longevity and performance.

Clean filter: Twist and lift out filter assembly weekly; rinse under tap.
Clean spray arms: Remove and check for clogs in nozzles.
Wipe door seals: Use damp cloth to remove debris.
Descale monthly: Use dishwasher cleaner or run empty cycle with 250 ml vinegar.
Check and refill salt and rinse aid as indicated by LEDs.

CAUTION! Unplug before maintenance. Do not use abrasive cleaners on interior.

Regulatory Information

CE marked. Complies with EU directives for low voltage, electromagnetic compatibility, and eco-design. Waste electrical products must not be disposed of with household waste. Please recycle according to local regulations. For support, visit www.beko.com or contact your local Beko service center.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Dishwasher won't start	Door not closed/power	Ensure door is latched; check power outlet and fuse.
Poor cleaning results	Spray arm blocked/filter	Clean filter and spray arms; check detergent is fresh.
Water not draining	Drain hose clogged/kinked	Check hose for kinks; clean filter; ensure drain height is correct.
Leaking water	Door seal damaged/hose	Inspect door seal for debris/damage; check hose connections.
Unusual noise	Dish obstructing spray arm	Stop cycle, rearrange dishes ensuring spray arms rotate freely.
Salt/Rinse Aid LED on	Low level	Refill corresponding compartment.
Error Code E1	Water inlet fault	Check water tap is on; inlet hose not kinked; filter clean.
Error Code E3	Heating fault	Unplug for 5 minutes, restart. If persists, call service.

Reset: Unplug for 5 minutes, then restart.

Service: Contact authorized Beko service. Keep model number (DIN28426) ready.