beko dishwasher DVN04320 manual

The Beko DVN04320 is a freestanding dishwasher with a 12-place setting capacity, featuring multiple wash programs, energy efficiency class A, delay start function, child lock, and half-load option. It includes a cutlery basket, adjustable upper basket, salt and rinse aid indicators, and an aquastop safety feature. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Loading the Dishwasher 7. Using Wash Programs 8. Maintenance & Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Control panel with digital display, adjustable upper basket, cutlery basket, filter system, salt and rinse aid compartments, inlet and drain hoses.

FeatureDescription
Capacity12 standard place settings
Wash ProgramsAuto, Intensive, Eco, Quick, Glass, Delicate
Delay StartProgram start delay from 1 to 24 hours
Child LockPrevents accidental program changes
Half Load OptionSaves water and energy for smaller loads
AquastopLeak protection system
Salt IndicatorAlerts when water softener salt is low
Rinse Aid IndicatorAlerts when rinse aid needs refilling
Energy ClassA (energy efficient)
Noise Level52 dB (quiet operation)

Installation

Unpack and inspect contents. Ensure location is near water supply, drain, and power outlet.

  1. Position dishwasher: Place on level floor near sink area.
  2. Connect water inlet: Attach inlet hose to cold water tap (ensure filter is clean).
  3. Connect drain hose: Secure to sink drain or standpipe (use provided clamp).
  4. Electrical connection: Plug into grounded 220-240V, 50Hz outlet.
  5. Level the appliance: Adjust feet to ensure stability.

WARNING! Do not use extension cords. Ensure water connections are tight to prevent leaks.

First-Time Setup

Before first use, prepare dishwasher and set basic functions.

  1. Remove transport materials: Take out any brackets or foam inside tub.
  2. Fill salt dispenser: Add special dishwasher salt to softener unit (located at bottom of tub).
  3. Fill rinse aid: Pour rinse aid into designated compartment in door.
  4. Run initial wash: Select Intensive program without dishes to clean interior.
  5. Set water hardness: Adjust softener setting according to local water hardness (see manual chart).

CAUTION! Use only dishwasher salt and rinse aid. Do not use table salt or other substitutes.

Specifications

Controls and Settings

Control Panel: POWER button, program selection dial, digital display, option buttons (Delay Start, Half Load, Child Lock).

Programs: Auto (senses soil level), Intensive (for heavily soiled), Eco (energy saving), Quick (58 minutes), Glass (gentle for crystal), Delicate (for fine china).

Options: Delay Start (1-24h), Half Load (for fewer dishes), Extra Dry (enhanced drying), Child Lock (press and hold for 3 seconds). Display shows: remaining time, salt/rinse aid indicators, program status.

Loading the Dishwasher

Proper loading ensures optimal cleaning and prevents damage.

  1. Scrape off large food residues (no need to pre-rinse).
  2. Lower basket: Pots, pans, plates (face inward).
  3. Upper basket: Glasses, cups, small plates (secure in racks).
  4. Cutlery basket: Place knives, forks, spoons (handles down for safety).
  5. Adjust upper basket: Can be raised/lowered for tall items.
  6. Ensure spray arms rotate freely; do not block with large items.

Tip: Place delicate items in top basket only. Do not overload.

Using Wash Programs

Select program based on load type and soil level.

  1. Turn on: Press POWER button.
  2. Select program: Turn dial to desired program (see program guide).
  3. Add options: Press option buttons if needed (e.g., Delay Start).
  4. Start: Close door firmly; wash begins automatically.
  5. During wash: Display shows remaining time; door locks for safety.
  6. After completion: Beep sounds; display shows "End." Wait a few minutes before opening (steam may escape).
  7. Unloading: Remove lower basket first to avoid dripping on items below.

WARNING! Do not open door during wash cycle. Hot water and steam can cause burns.

Maintenance & Care

Regular maintenance ensures performance and longevity.

  1. Clean filter: Remove and rinse under water weekly.
  2. Check spray arms: Ensure holes are not clogged; rotate freely.
  3. Refill salt: When indicator lights, add salt to softener (only when dishwasher is off).
  4. Refill rinse aid: When indicator lights, fill compartment (adjust dosage if needed).
  5. Exterior cleaning: Wipe with damp cloth; do not use abrasive cleaners.
  6. Monthly cleaning: Run empty cycle with dishwasher cleaner or vinegar to remove grease.

CAUTION! Unplug before any maintenance. Do not touch heating element.

Regulatory Information

CE marked; complies with EU directives for safety and electromagnetic compatibility. Energy label class A. Waste electrical products must not be disposed of with household waste. Please recycle according to local regulations. For support, visit www.beko.com or contact customer service at 0333 207 9710 (UK).

Troubleshooting

SymptomPossible CauseCorrective Action
Dishwasher won't startPower supply/doorCheck plug and power; ensure door is closed properly.
Poor cleaning resultsLoading/filter/saltRearrange load; clean filter; check salt level and water hardness setting.
Water not drainingDrain hose cloggedCheck hose for kinks; clean filter; ensure drain height is correct (40-100 cm).
Leaking waterHose connections/inlet valveTighten connections; check door seal for debris; ensure dishes are not blocking spray arm.
Unusual noiseSpray arm/dishesEnsure spray arms rotate freely; check dishes are not touching spray arm.
Salt indicator flashingSalt low/incorrect settingRefill salt; reset indicator by pressing program button for 3 seconds.

Reset: Unplug for 5 minutes, then restart.

Service: 0333 207 9710; www.beko.com

beko dishwasher DVN04320 manual © - All Rights Reserved 2025