beko prosmart inverter manual reset

The Beko ProSmart Inverter series features advanced inverter technology for energy-efficient operation. A manual reset may be required to resolve error codes, restore normal function after a power surge, or clear minor system faults. This guide covers the reset procedure, safety precautions, common scenarios requiring a reset, and troubleshooting steps if the reset does not resolve the issue.

1. Safety Precautions 2. When to Perform a Manual Reset 3. Step-by-Step Reset Procedure 4. Post-Reset Initialization 5. Common Error Codes & Resets 6. If Reset Does Not Work 7. Preventing Unnecessary Resets 8. Technical Specifications 9. Warranty & Support

Safety Precautions

Before attempting any reset, ensure safety to prevent injury or damage to the appliance.

Precaution	Description
Power Disconnect	Unplug the appliance from the mains power supply before any procedure.
Wait Time	Allow at least 10-15 minutes for capacitors to discharge after disconnection.
No Water Exposure	Ensure hands and work area are dry. Do not reset with wet hands.
Stable Surface	Ensure the appliance is on a flat, stable surface and is not operating.
No Forced Buttons	Press reset or control buttons gently; do not apply excessive force.
Refer to Manual	Check your specific model's manual for model-specific reset instructions.
Child Safety	Keep children away from the appliance during the reset process.
Visual Inspection	Check for obvious damage, burns, or loose wires before proceeding.

When to Perform a Manual Reset

A manual reset is typically needed in the following situations:

Error Code Display: An error code (e.g., E01, E04) appears and persists.
Unresponsive Controls: The appliance does not respond to button presses or remote commands.
Post-Power Outage: Appliance behaves erratically after a power failure or surge.
Inverter Lock: The inverter compressor or motor seems locked or is not starting.
Minor Software Glitch: Settings are lost or functions operate incorrectly.

WARNING! Do not attempt a reset if there is smoke, burning smell, or visible electrical damage. Contact service immediately.

Step-by-Step Reset Procedure

Follow these general steps to perform a full system reset on a Beko ProSmart Inverter appliance.

Power Off: Press the power button to turn the appliance off.
Unplug: Disconnect the power plug from the wall socket.
Wait: Leave the appliance unplugged for a minimum of 10-15 minutes. This allows the inverter control board to fully power down and clear temporary memory.
Power Restore: Plug the appliance back into the mains power socket securely.
Power On: Press the power button to turn the appliance on.
Test Basic Function: Run a basic cycle or function to see if the error is cleared and normal operation resumes.

For models with a dedicated Reset Button: After unplugging, locate the small reset button (often near the display or on the control panel). Use a paperclip to press and hold for 5-10 seconds while plugged out. Then plug in and power on.

Post-Reset Initialization

After a successful reset, the appliance will go through an initialization sequence.

Self-Test: The control panel may light up all indicators briefly as the system runs a self-diagnostic.
Default Settings: Some user-defined settings (like timers or special modes) may revert to factory defaults.
Inverter Re-calibration: The inverter compressor may run at a specific speed to recalibrate. This is normal and may cause unusual sounds for a few minutes.
Wait for Stability: Allow the appliance 5-10 minutes of idle time after reset before starting a full operation cycle.

Tip: Consult your manual to reconfigure any preferred settings after the reset is complete.

Common Error Codes & Resets

Some frequent error codes on Beko ProSmart Inverter models that may be resolved with a manual reset.

Error Code	Likely Meaning	Reset as First Action?
E01 / E1	Communication fault with main board	Yes, often resolves temporary glitches.
E03 / E3	Temperature sensor issue	Yes, but if persistent, sensor may be faulty.
E04 / E4	Motor or inverter compressor error	Yes, a reset can clear a soft lock.
E05 / E5	Water supply or drain issue	Check for blockages first, then reset.
E09 / E9	Electronic control fault	Yes, a full power cycle reset is recommended.
F-- / dE	Door/door lock error	Ensure door is closed properly, then reset.

If Reset Does Not Work

If the manual reset does not clear the error or restore function, proceed with these steps.

Repeat Reset: Ensure you waited the full 15 minutes unplugged. Try a second time.
Check Power Supply: Test the wall outlet with another device. Ensure voltage is stable.
Inspect Filters & Vents: Clean any air filters (for ACs/fridges) or drain filters (for washers). Overheating can cause faults.
Consult Manual: Look for a model-specific reset combination (e.g., holding two buttons for 5 seconds).
Contact Support: If the error persists, the issue may be hardware-related (failed sensor, inverter board, compressor).

Service Contact: Have your model number ready. It is usually found on the rating plate inside the door or on the rear.

Preventing Unnecessary Resets

Proper use and maintenance can reduce the need for manual resets.

Use a Surge Protector: Protects the sensitive inverter electronics from voltage spikes.
Avoid Overloading: Do not exceed the recommended capacity for washers, dryers, or refrigerators.
Regular Cleaning: Keep filters, vents, and coils clean to ensure proper operation and prevent overheating.
Stable Power: If power outages are frequent, consider a UPS for critical appliances.
Correct Settings: Use appropriate programs and settings for your load type.

Technical Specifications

Technology: ProSmart Inverter Motor/Compressor.
Power Supply: 220-240V~, 50Hz (or as per regional model).
Reset Method: Full power cycle (disconnect from mains).
Control Board: Microprocessor-based with error memory.
Typical Reset Time: 10-15 minutes of being unplugged.
Factory Reset: Often requires a specific button sequence; consult manual.
Warranty Impact: Performing a manual reset does not void warranty unless damage is caused.

Warranty & Support

Beko appliances come with a standard manufacturer's warranty. The manual reset procedure is a user-recommended troubleshooting step.

Before Calling for Service: Note the model number, serial number, and any displayed error code. Inform the technician if you performed a reset and the result.

Official Support:
Website: www.beko.com
Customer Service: Check local Beko website for regional contact numbers.
Authorized Service Centers: Use the service locator on the official website.

Disclaimer: This guide is for informational purposes. Always refer to the official user manual for your specific Beko ProSmart Inverter model for accurate instructions.